Configuring Static Public IP Communication

If your terminal is registered to a base that will communicate with the Moneris Host over the Internet using public IP with static addressing, you will need to set up these parameters for the base.

Before you begin you will need:

To navigate through the menus:

- Scroll down: press
the key_f1-r.jpg key to move the highlight bar down.
- Scroll up: press
the key_f3-r.jpg key to move the highlight bar up.
- Select a
highlighted item: press the key_okay-r.jpg  key.

For information about the keys...

1.  Follow one of the procedures below:

If terminal has NEVER been initialized:

If terminal has already been initialized:

From the TERMINAL SETUP REQUIRED screen:

a.  Press the key_admin-r.jpg  key.
The MAIN MENU appears.

b.  Scroll down to CONFIGURATION, and press the key_okay-r.jpg  key.
The CONFIG FUNCS menu appears.

c.  Scroll down to GENERAL PARAMS, and press the key_okay-r.jpg  key.

If the SWIPE ADMIN CARD prompt appears, swipe the POS Admin card.

The GENERAL PARAMETERS menu appears.

d.  Press the key_okay-r.jpg  key to select COMMS TYPE.
The COMMUNICATION TYPE menu appears.

e.  Scroll to ETHERNET, and press the key_okay-r.jpg  key.
The BASE IP SETUP menu appears.

f. Go to step 2 below.

From the READY screen:

a. Set the COMMS TYPE parameter as ETHERNET.  

b. Set the HOST SETUP parameter as PUBLIC.

c.  Press the key_admin-r.jpg  key.
The MAIN MENU appears.

d.  Scroll down to CONFIGURATION, and press the key_okay-r.jpg  key.
The CONFIG FUNCS menu appears.

e.  Scroll down to BASE CONFIG, and press the key_okay-r.jpg  key.

If the SWIPE ADMIN CARD prompt appears, swipe the POS Admin card.

The BASE CONFIG menu appears.

f. Scroll down to BASE IP SETUP, and press the key_okay-r.jpg  key. The BASE IP SETUP menu appears.

g. Go to step 2 below.

 

2.  Configure the static IP parameters:

a.  Press the key_okay-r.jpg  key to select ETHERNET SETUP.
The ETHERENT SETUP menu appears.

b.  Press the key_okay-r.jpg  key to select ETHERNET TYPE.
The ETHERNET TYPE setup menu appears.

c.  Scroll up to STATIC, and press the key_okay-r.jpg  key.
The ETHERNET SETUP menu appears listing the static parameters for the base.

d.  Scroll down to BASE IP ADDR, and press the key_okay-r.jpg  key.
The ENTER BASE IP ADDRESS entry screen appears.

e.  Key in the base's IP Address, and press the key_okay-r.jpg  key.
The ETHERNET SETUP menu appears.

f.  Scroll down to BASE MASK ID, and press the key_okay-r.jpg  key.
The ENTER MASK ID entry screen appears.

g.  Key in the base's Mask ID, and press the key_okay-r.jpg  key.
The ETHERNET SETUP menu appears.

h.  Scroll down to BASE GATEWAY, and press the key_okay-r.jpg  key.
The ENTER GATEWAY ADDRESS entry screen appears.

k.  Key in the base's Gateway Address, and press the key_okay-r.jpg  key.
The ETHERNET SETUP menu appears.

l.  Press the key_cancel.jpg key once.
The BASE IP SEUP menu appears.

m.  Enter the base's DNS Addresses:

i.  Scroll down to DNS SETUP, and press the key_okay-r.jpg  key.

ii.  Press the key_okay-r.jpg  key to select PRIM ADDRESS.
The ENTER PRIMARY ADDRESS entry screen appears.

iii.  Key in the base's Primary DNS Address, and press the key_okay-r.jpg  key.

iv.  Scroll down to SEC ADDRESS, and press the key_okay-r.jpg  key.
The ENTER SECONDARY ADDRESS entry screen appears.

v.  Key in the base's secondary DNS address, and press the key_okay-r.jpg  key.

vi.  Press the key_cancel.jpg key once.
The BASE IP SETUP menu appears.

3. Test the terminal's connectivity to the Moneris Host:

a. From the BASE IP SETUP menu, press the key_cancel.jpg key once.
The REBOOT TERMINAL message appears.

b.  Wait for the terminal to finish rebooting and then for it to return to the TERMINAL SETUP REQUIRED screen (or READY screen or REINITILIZATION REQUIRED screen).
c.  Press the key_admin-r.jpg  key twice, key in 17, and press the key_okay-r.jpg  key .  

If SWIPE ADMIN CARD appears, swipe the POS Admin card.  

d.  Scroll down to BASE IP SETUP, and press the key_okay-r.jpg  key .

e.  When the BASE IP SETUP menu appears, press the key_cancel.jpg key once.

f. When the TCP HOST CONNECTION OK PRESS OK prompt appears, press the key_okay-r.jpg  key  to return to the TERMINAL SETUP REQUIRED screen (or the READY screen or REINITIALIZATION REQUIRED screen).

4. Go back to Configuring Your Terminal.